中国电气工程学报（英文） ›› 2024, Vol. 10 ›› Issue (2): 16-29.doi: 10.23919/CJEE.2023.000045
-
收稿日期:2023-08-08修回日期:2023-09-29接受日期:2023-10-15出版日期:2024-06-25发布日期:2024-07-01
Overview of Torque Ripple Minimization Methods for Permanent Magnet Synchronous Motors Based on Harmonic Injection*
Peng Yi, Wenzhi Zheng, Xianglin Li*
- College of Electrical Engineering, Qingdao University, Qingdao 266071, China
-
Received:2023-08-08Revised:2023-09-29Accepted:2023-10-15Online:2024-06-25Published:2024-07-01 -
Contact:* E-mail:lxllcc@126.com -
About author:Peng Yi received the B.S. degree in Automotive Engineering from Jilin University, Changchun, China in 2011, M.S. and Ph.D. degrees in Automotive Engineering from Tongji University, Shanghai, China in 2014 and 2020, respectively. He has been with the College of Electrical Engineering of Qingdao University since 2020. His current research interests include torque ripple minimization, loss characteristics and electromagnetic vibration of PMSM.
Wenzhi Zheng received the B.S. degree in Electrical Engineering from Qingdao University, Shandong Province, China in 2021 and is currently pursuing the M.S. degree in Electrical Engineering from Qingdao University. His current research direction is electromagnetic vibration of PMSM used in electrical vehicle.
Xianglin Li (M’15) received the B.S. and M.S. degrees from China University of Petroleum (East China), Qingdao, China, in 2007 and 2010, respectively, and the Ph.D. degree from Southeast University, Nanjing, China, in 2015, all in Electrical Engineering. He was a joint-supervised Ph.D. student with the Wisconsin Electric Machine and Power Electronics Consortium (WEMPEC), University of Wisconsin-Madison, Madison, WI, USA, from Sept. 2012 to Sept. 2013, and a Research Assistant with the Department of Electrical and Electronic Engineering, University of Hong Kong, Hong Kong, China, from Jul. 2014 to Jan. 2015.
From 2015 to 2019, he was an Associate Professor with China University of Petroleum (East China). Since 2020, he has been a Professor in the College of Electrical Engineering, Qingdao University. His research interests mainly include design, analysis, and control of electrical machines, especially for PM brushless machines and high temperature superconducting machines, etc. -
Supported by:*National Natural Science Foundation of China (52107052), in part by the Natural Science Foundation of Shandong Province (ZR2021QE222 and ZR2021YQ33).
引用本文
. [J]. 中国电气工程学报（英文）, 2024, 10(2): 16-29.
Peng Yi, Wenzhi Zheng, Xianglin Li. Overview of Torque Ripple Minimization Methods for Permanent Magnet Synchronous Motors Based on Harmonic Injection*[J]. Chinese Journal of Electrical Engineering, 2024, 10(2): 16-29.
| [1] D Wang, C Peng, X Wang.Research on different design approaches to mitigate torque ripple and electromagnetic vibration for high-performance electric vehicle traction machine.Journal of Electrical Engineering, 2021, 16(4): 42-49. [2] W Chu, Z Zhu.Investigation of torque ripples in permanent magnet synchronous machines with skewing.IEEE Transactions on Magnetics, 2013, 49(3): 1211-1220. [3] M Zhou, X Zhang, W Zhao, et al.Influence of magnet shape on the cogging torque of a surface-mounted permanent magnet motor.Chinese Journal of Electrical Engineering, 2019, 5(4): 40-50. [4] C M Spargo, B C Mecrow, J D Widmer.A seminumerical finite-element postprocessing torque ripple analysis technique for synchronous electric machines utilizing the air-gap Maxwell stress tensor. IEEE Transactions on Magnetics, 2014, 50(5): 1-9. [5] K Wang, Z Zhu, G Ombach, et al.Average torque improvement of interior permanent-magnet machine using third harmonic in rotor shape.IEEE Transactions on Industrial Electronics, 2014, 61(9): 5047-5057. [6] J Liang, A Parsapour, Z Yang, et al.Optimization of air-gap profile in interior permanent-magnet synchronous motors for torque ripple mitigation. IEEE Transactions on Transportation Electrification, 2019, 5(1): 118-125. [7] L Alberti, M Barcaro, N Bianchi.Design of a low torque ripple fractional-slot interior permanent magnet motor.IEEE Transactions on Industry Applications, 2014, 50(3): 1801-1808. [8] G Wang, Y Yu, R Yang, et al.Dead-time compensation of space vector PWM inverter for induction motor.Proceedings of the CSEE, 2008, 28(15): 79-83. [9] S H Hwang, J M Kim.Dead time compensation method for voltage-fed PWM inverter.IEEE Transactions on Energy Conversion, 2010, 25(1): 1-10. [10] J Yu, P Zhu, Y Xu.Dead zone compensation strategy for inverter of PMSM based on direct axis voltage analysis.Journal of Electrical Engineering, 2021, 16(4): 51-58. [11] N Bedetti, S Calligaro, R Petrella.Self-commissioning of inverter dead-time compensation by multiple linear regression based on a physical model.IEEE Transactions on Industry Applications, 2015, 51(5): 3954-3964. [12] G Liu, D Wang, Y Jin, et al.Current detection independent dead-time compensation method based on terminal voltage A/D conversion for PWM VSI.IEEE Transactions on Industrial Electronics, 2017, 64(10): 7689-7699. [13] D H Lee, J W Ahn.A simple and direct dead-time effect compensation scheme in PWM-VSI.IEEE Transactions on Industry Applications, 2014, 50(5): 3017-3025. [14] Y Liao, J Yao, S Yang.Analysis and elimination method of harmonics produced by forward voltage drop of ACEG excitation power source.Proceedings of the CSEE, 2004, 24(4): 151-156. [15] J T Boys, P G Handley.Harmonic analysis of space vector modulated PWM waveforms.IEE Proceedings, 1990, 137(4): 197-204. [16] Y Huang, Y Xu, W Zhang, et al.Hybrid RPWM technique based on modified SVPWM to reduce the PWM acoustic noise.IEEE Transactions on Power Electronics, 2019, 34(6): 5667-5674. [17] P Yi, Y Yin, X Wang, et al.PMSM torque ripple minimization based on novel low carrier ratio PWM technique.IEEE Transactions on Power Electronics, 2022, 37(9): 11071-11084. [18] Y Huang, Y Xu, W Zhang, et al.Modified single-edge SVPWM technique to reduce the switching losses and increase PWM harmonics frequency for three-phase VSIs.IEEE Transactions on Power Electronics, 2020, 35(10): 10643-10653. [19] V S S P K Hari, G Narayanan. Space-vector-based hybrid PWM technique to reduce peak-to-peak torque ripple in induction motor drives.IEEE Transactions on Industry Applications, 2015, 52(2): 1489-1499. [20] W Liang, J Wang, P C K Luk, et al. Analytical modeling of current harmonic components in PMSM drive with voltage-source inverter by SVPWM technique. IEEE Transactions on Energy Conversion, 2014, 29(3): 673-680. [21] I Jeong, K Nam.Analytic expressions of torque and inductances via polynomial approximations of flux linkages.IEEE Transactions on Magnetics, 2015, 51(7): 1-9. [22] A Piippo, J Luomi.Torque ripple reduction in sensorless PMSM drives.32nd Annual Conference on IEEE Industrial Electronics (IECON 2006), November 6-10, 2006, Paris, France. Piscataway: IEEE, 2006: 920-925. [23] P Mattavelli, L Tubiana, M Zigliotto.Torque-ripple reduction in PM synchronous motor drives using repetitive current control.IEEE Transactions on Power Electronics, 2005, 20(6): 1423-1431. [24] A Madani, J P Barbot, F Colamartino, et al.Reduction of torque pulsations by inductance harmonics identification of a permanent-magnet synchronous machine.Proceedings of the 1995 IEEE Conference on Control Applications, September 28-29, 1995, Albany, NY, USA. Piscataway: IEEE, 1995: 787-792. [25] C Marchand, A Razek.Optimal torque operation of digitally controlled permanent magnet synchronous motor drives.IEE Proceedings-B Electric Power Applications, 1993, 140(3): 232-240. [26] G H Lee, S I Kim, J P Hong, et al.Torque ripple reduction of interior permanent magnet synchronous motor using harmonic injected current.IEEE Transactions on Magnetics, 2008, 44(6): 1582-1585. [27] L Springob, J Holtz.High-bandwidth current control for torque-ripple compensation in PM synchronous machines. IEEE Transactions on Industrial Electronics, 1998, 45(5): 713-721. [28] F Colamartino, C Marchand, A Razek.Torque ripple minimization in permanent magnet synchronous servodrive.IEEE Transactions on Energy Conversion, 1999, 14(3): 616-621. [29] H Jia, M Cheng, W Hua, et al.Cogging torque compensation for flux-switching permanent magnet motor based on current harmonics injection.Proceedings of the CSEE, 2009, 29(27): 83-89. [30] N Nakao, K Akatsu.Torque ripple suppression of permanent magnet synchronous motors considering total loss reduction.5th Annual IEEE Energy Conversion Congress and Exhibition (ECCE 2013), September 15-19, 2013, Denver, CO, USA. Washington: IEEE, 2013: 3880-3887. [31] N Nakao, K Akatsu.Suppressing pulsating torques: Torque ripple control for synchronous motors.IEEE Industry Applications Magazine, 2014, 20(6): 33-44. [32] J Holtz, L Springob.Identification and compensation of torque ripple in high-precision permanent magnet motor drives.IEEE Transactions on Industrial Electronics, 1996, 43(2): 309-320. [33] J Tan.Selection of slot/pole number combinations for BLDCM with concentrated windings.Micromotors, 2008, 2008(2): 74-79. [34] S Wang, J Kang, M Zhong, et al.Overviews of torque ripple suppression method with permanent magnet synchronous motor used in electric vehicles.Journal of Power Supply, 2016, 14(5): 24-32. [35] H Che, E Levi, M Jones, et al.Current control methods for an asymmetrical six-phase induction motor drive.IEEE Transactions on Power Electronics, 2014, 29(1): 407-417. [36] R Bojoi, F Farina, M Lazzari, et al.Analysis of the asymmetrical operation of dual three-phase induction machines.IEEE International Electric Machines and Drives Conference (IEMDC 2003), June 1-4, 2003, Madison, WI, USA. Piscataway: IEEE, 2003: 429-435. [37] R J Strahan.Energy conversion by nonlinear permanent magnet machines.IEE Proceedings-Electric Power Applications, 1998, 145(3): 193-198. [38] J Li, Y Yong.Model of permanent magnet synchronous motor considering saturation and rotor flux harmonics.Proceedings of the CSEE, 2011, 31(3): 60-66. [39] C Lai, G Feng, K Mukherjee, et al.Torque ripple modeling and minimization for interior PMSM considering magnetic saturation. IEEE Transactions on Power Electronics, 2017, 33(3): 2417-2429. [40] I Boldea, S A Nasar.A general equivalent circuit (GEC) of electric machines including cross-coupling saturation and frequency effects.IEEE Transactions on Energy Conversion, 1988, 3(3): 689-695. [41] B Stumberger, G Stumberger, D Dolinar, et al.Evaluation of saturation and cross-magnetization effects in interior permanent-magnet synchronous motor.IEEE Transactions on Industry Applications, 2003, 39(5): 1264-1271. [42] H Li, J Zhang, Y Luo.Finite element analysis of PMSM steady state parameters considering cross-saturation effect.Proceedings of the CSEE, 2012, 32(12): 104-110. [43] J F Gieras, E Santini, M Wing.Calculation of synchronous reactances of small permanent-magnet alternating-current motors: Comparison of analytical approach and finite element method with measurements.IEEE Transactions on Magnetics, 1998, 34(5): 3712-3720. [44] H Li, J Zhang, M Liu.An improved calculation method for steady-state parameters of PMSM with T-S FEM.Transactions of China Electrotechnical Society, 2012, 27(4): 35-41. [45] X Wang, P Yi, Z Zhou, et al.Improvements in the permanent magnet synchronous motor torque model using incremental inductance.IET Electric Power Applications, 2020, 14(1): 109-118. [46] Z Zhong, S Jiang, Y Zhou, et al.Active torque ripple reduction based on an analytical model of torque.IET Electric Power Applications, 2017, 11(3): 331-341. [47] W Tong, S Li, X Pan, et al.Analytical model for cogging torque calculation in surface-mounted permanent magnet motors with rotor eccentricity and magnet defects.IEEE Transactions on Energy Conversion, 2020, 35(4): 2191-2200. [48] L Wu, Z Zhu, D A Staton, et al.Comparison of analytical models of cogging torque in surface-mounted PM machines.IEEE Transactions on Industrial Electronics, 2012, 59(6): 2414-2425. [49] K Zhang, Y Kang, J Xiong, et al.Direct repetitive control of SPWM inverters for UPS purpose.IEEE Transactions on Power Electronics, 2003, 18(3): 784-792. [50] T Jahns, W Soong.Pulsating torque minimization techniques for permanent magnet AC motor drives: A review.IEEE Transactions on Industrial Electronics, 1996, 43(2): 321-330. [51] A G Yepes, F D Freijedo, Ó Lopez, et al.Analysis and design of resonant current controllers for voltage-source converters by means of nyquist diagrams and sensitivity function.IEEE Transactions on Industrial Electronics, 2011, 58(11): 5231-5250. [52] J Gao, X Wu, S Huang, et al.Torque ripple minimisation of permanent magnet synchronous motor using a new proportional resonant controller.IET Power Electronics, 2017, 10(2): 208-214. [53] C Xia, B Ji, Y Yan.Smooth speed control for low-speed high-torque permanent-magnet synchronous motor using proportional-integral-resonant controller.IEEE Transactions on Industrial Electronics, 2015, 62(4): 2123-2134. [54] H Chuan, S M Fazeli, Z Wu, et al.Mitigating the torque ripple in electric traction using proportional integral resonant controller.IEEE Transactions on Vehicular Technology, 2020, 69(10): 10820-10831. [55] B Guan, Y Zhao, Y Ruan.Torque ripple minimization in interior PM machines using FEM and multiple reference frames.2006 1st IEEE Conference on Industrial Electronics and Applications (ICIEA 2006), May 24-26, 2006, Singapore, Singapore. Piscataway: IEEE, 2006: 1-6. [56] Y Liao, S Zhen, R Liu.Torque ripple suppression of permanent magnet synchronous motor by the harmonic injection.Proceedings of the CSEE, 2011, 31(21): 119-127. [57] G Feng, C Lai, N C Kar.Speed harmonic based decoupled torque ripple minimization control for permanent magnet synchronous machine with minimized loss.IEEE Transactions on Energy Conversion, 2020, 35(4): 1796-1805. [58] P Yi, X Wang, Z Sun.Research on PMSM harmonic coupling models based on magnetic co-energy.IET Electric Power Applications, 2019, 13(4): 571-579. [59] P Yi, X Wang, D Chen, et al.PMSM current harmonics control technique based on speed adaptive robust control.IEEE Transactions on Transportation Electrification, 2022, 8(2): 1794-1806. [60] S Jiang, Y Wang.Internal mode decoupled harmonic current tracking for vehicular PMSMs noise reduction.IEEE Transactions on Vehicular Technology, 2022, 71(12): 12711-12721. [61] F Morel, X Linshi, J Retif, et al.A comparative study of predictive current control schemes for a permanent-magnet synchronous machine drive.IEEE Transactions on Industrial Electronics, 2009, 56(7): 2715-2728. [62] Y Zhang, H Yang.Two-vector-based model predictive torque control without weighting factors for induction motor drives.IEEE Transactions on Power Electronics, 2016, 31(2): 1381-1390. [63] X Wang, D Sun.Three-vector-based low-complexity model predictive direct power control strategy for doubly fed induction generators.IEEE Transactions on Power Electronics, 2017, 32(1): 773-782. [64] Z Zhou, C Xia, Y Yan, et al.Torque ripple minimization of predictive torque control for PMSM with extended control set.IEEE Transactions on Industrial Electronics, 2017, 64(9): 6930-6939. [65] X Yuan, C Zhang, S Zhang.Torque ripple suppression for open-end winding permanent-magnet synchronous machine drives with predictive current control.IEEE Transactions on Industrial Electronics, 2019, 67(3): 1771-1781. [66] M N Uddin, M M Rahman.Online torque-flux estimation-based nonlinear torque and flux control scheme of IPMSM drive for reduced torque ripples.IEEE Transactions on Power Electronics, 2019, 34(1): 636-645. [67] X Li, Z Xue, L Zhang, et al.A low-complexity three-vector-based model predictive torque control for SPMSM.IEEE Transactions on Power Electronics, 2021, 36(11): 13002-13012. [68] X Li, Z Xue, X Yan, et al.Low-complexity multivector-based model predictive torque control for PMSM with voltage preselection.IEEE Transactions on Power Electronics, 2021, 36(10): 11726-11738. [69] L Chen, H Xu, X Sun, et al.Three-vector-based model predictive torque control for a permanent magnet synchronous motor of EVs.IEEE Transactions on Transportation Electrification, 2021, 7(3): 1454-1465. [70] G Feng, C Lai, N C Kar.An analytical solution to optimal stator current design for PMSM torque ripple minimization with minimal machine losses.IEEE Transactions on Industrial Electronics, 2017, 64(10): 7655-7665. [71] P Yi, X Wang, Z Sun.Interior permanent magnet synchronous motor minimum current harmonics torque ripple suppression strategy based on magnetic co-energy model.IET Electric Power Applications, 2020, 14(2): 234-244. [72] G Feng, C Lai, N C Kar.Practical testing solutions to optimal stator harmonic current design for PMSM torque ripple minimization using speed harmonics.IEEE Transactions on Power Electronics, 2018, 33(6): 5181-5191. [73] L Yan, Y Liao, H Lin, et al.Torque ripple suppression of permanent magnet synchronous machines by minimal harmonic current injection.IET Power Electronics, 2019, 12(6): 1368-1375. [74] X Wang, H Wang, Y Liu, et al.Multi-objective control harmonic current solution for permanent magnet synchronous motor.2022 IEEE Transportation Electrification Conference and Expo,Asia-Pacific (ITEC Asia-Pacific 2022), October 28-31, 2022, Haining, China. Piscataway: IEEE, 2022: 1-6. |
| No related articles found! |
| 阅读次数 | ||||||
|
全文 |
|
|||||
|
摘要 |
|
|||||